Exterior

Access Gloss Enamel

PrintEmail

Prominent Paints Access Gloss Enamel is ideal for use as a final coat on interior and exterior cement plaster, metal, wood, or previously painted surfaces in sound condition. It is washable and will not leave dull patches when scrubbed.

Products Applications:
Trims (Interior), Trims (Exterior), Trims (Interior & Exterior), Wood (Exterior), Wood (Interior), Wood (Interior & Exterior), Interior, Exterior and Interior & Exterior

Purchase:
Access Gloss Enamel is available white, black, golden brown and cream in the following pack sizes: 1lt and 5lt


Description

White and standard colours as per latest colour brochure. Eye tinting can be done for pastel colours from white.

Please note: Every care has been taken to ensure that the colours displayed on this website reflect the actual paint colour as accurately as possible. Colours may vary due to your screen settings and resolution. Always consult a Prominent Paints colour card or stripe card before making your final colour choice.

 
WHITE
 
CREAM
 
GOLDEN BROWN
 
BLACK

Appearance: Gloss.
Spreading Rate: 6-8 m²/l dependent on surface texture and porosity.
Solids: ± 33% by mass and ± 25% by volume.
Density: ± 1.00kg/l.
Recommended Dry Film Thickness: ± 40μm per coat
Viscosity at 23°C: ± 100Kμ.
Flash Point: 38°C minimum.
Respecting the environment: Dispose of excess product and containers in a responsible manner without harming the environment.
Storage:

  • Keep containers properly sealed. 
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt and 5Lt

 

 

Features

  • Durable
  • Scrubable
  • Ease of application
  • Glossy finish resists scuffing and marring
  • Withstands scrubbing with detergents
  • Viscosity designed to give easy brushing

Intended Usages

  • Final coat for correctly prepared and primed interior and exterior cement plaster, metal, wood or previously painted surfaces in sound condition.

Application Details

  • Mixing: Stir well before use with a flat paddle to a homogenous consistency. Stir occasionally during use.
  • Method: Brush, roller (use short nap roller - mohair).
  • Thinning: ProGold Mineral Turpentine if required up to maximum 10%.
  • Cleaning: ProGold Mineral Turpentine.

Application Conditions:

  • Surface Temperature between 5°C and 40°C.
  • Ambient Temperature between 5°C and 40°C.
  • Relative Humidity between 10% and 85%.
  • Ideally, apply when the temperature of the substrate is at least 2ºC above dew point and if possible away from direct sunlight.
 

Touch dry: 4 hours at 23°C. 

Recoating time: 16h at 23ºC.

Full cure: 7 – 21 day depending on weather conditions.

Note: higher temperatures will accelerate the drying times (approximately halved for every 10°C increase) whilst lower temperatures will retard the drying times (approximately doubled for every 10°C decrease.

Requirements: 2 coats minimum.

Surface Preparations
Surfaces must be sound, clean and dry (moisture level below 15%) before painting.

New Work:

Cement plaster:

  • 1 coat Access Plaster Primer and 1 coat Prominent Select Universal Undercoat.

Gypsum plaster:

  • 1 coat Access Plaster Primer and 1 coat Prominent Select Universal Undercoat.

Metal (new)

  • Clean surface with ProGold Multi Surface Etch Cleaner with abrasive pad to remove any oil, paint and apply 1 coat Prominent Machinery Enamel Primer – Zinc phosphate or 2 coats Prominent Rust Primer.

Metal (rusted)

  • Remove rust. Clean surface with ProGold Multi Surface Etch Cleaner with abrasive pad, rinse with water and allow drying. Apply 2 coats Prominent Rust Primer and 1 coat Prominent Select Universal Undercoat.

Redecorating:
It is advisable to test the compatibility of coatings when redecorating is involved, i.e. paint a small section and then check the adhesion after 24 hours by applying a strip of masking tape and attempting to rip the paint off.

Gloss enamel:

  • Sand down to a matt finish, spot prime exposed metal with Prominent Rust Primer and apply 1 coat Prominent Select Universal Undercoat.

Sound matt emulsion paint:

  • Sand to matt finish, clean with ProGold General Purpose Cleaner diluted 1:10 with water and abrasive, rinse with water, allow drying and apply directly.

Sound sheen emulsion paint:

  • Sand to matt finish, clean with ProGold General Purpose Cleaner diluted 1:10 with water and abrasive, rinse with water, allow drying and apply directly.

Poor condition surfaces, i.e. excessive peeling:

  • Strip down and treat as per new work.

It is advisable to test the compatibility of coatings when redecorating is involved, i.e. paint a small section and then check the adhesion after 24 hours by applying a strip of masking tape and attempting to rip the paint off.

Limitations

  • Cannot be applied to unprimed surfaces.
  • Apply only under specified conditions.
  • Colour changes generally first require a coat of Prominent Paints Select Universal Undercoat.
  • Very cold conditions will lengthen the drying time.
  • Moisture content must not exceed 15%.
  • Apply to the correct spreading rates and adhere to the correct recoating times to prevent wrinkling.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • Wear a suitable dust mask if sanding.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In the event where product came in contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available from Prominent Paints Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • Wear a suitable dust mask if sanding.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In the event where product came in contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available from Prominent Paints Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

Copyright © 2019 Prominent Paints