Appearance: Gloss.
Spreading Rate: 6-8 m²/l dependent on surface texture and porosity.
Solids: ± 33% by mass and ± 25% by volume.
Density: ± 1.00kg/l.
Recommended Dry Film Thickness: ± 40μm per coat
Viscosity at 23°C: ± 100Kμ.
Flash Point: 38°C minimum.
Respecting the environment: Dispose of excess product and containers in a responsible manner without harming the environment.
Storage:

• Keep containers properly sealed. 
• Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt and 5Lt

 

 

Features

• Durable
• Scrubable
• Ease of application
• Glossy finish resists scuffing and marring
• Withstands scrubbing with detergents
• Viscosity designed to give easy brushing

Intended Usages

• Final coat for correctly prepared and primed interior and exterior cement plaster, metal, wood or previously painted surfaces in sound condition.

Application Details

• Mixing: Stir well before use with a flat paddle to a homogenous consistency. Stir occasionally during use.
• Method: Brush, roller (use short nap roller - mohair).
• Thinning: ProGold Mineral Turpentine if required up to maximum 10%.
• Cleaning: ProGold Mineral Turpentine.

Application Conditions:

• Surface Temperature between 5°C and 40°C.
• Ambient Temperature between 5°C and 40°C.
• Relative Humidity between 10% and 85%.
• Ideally, apply when the temperature of the substrate is at least 2ºC above dew point and if possible away from direct sunlight.

 

Touch dry: 4 hours at 23°C. 

Recoating time: 16h at 23ºC.

Full cure: 7 – 21 day depending on weather conditions.

Note: higher temperatures will accelerate the drying times (approximately halved for every 10°C increase) whilst lower temperatures will retard the drying times (approximately doubled for every 10°C decrease.

Requirements: 2 coats minimum.

Surface Preparations
Surfaces must be sound, clean and dry (moisture level below 15%) before painting.

New Work:

Cement plaster:

• 1 coat Access Plaster Primer and 1 coat Prominent Select Universal Undercoat.

Gypsum plaster:

• 1 coat Access Plaster Primer and 1 coat Prominent Select Universal Undercoat.

Metal (new)

• Clean surface with ProGold Multi Surface Etch Cleaner with abrasive pad to remove any oil, paint and apply 1 coat Prominent Machinery Enamel Primer – Zinc phosphate or 2 coats Prominent Rust Primer.

Metal (rusted)

• Remove rust. Clean surface with ProGold Multi Surface Etch Cleaner with abrasive pad, rinse with water and allow drying. Apply 2 coats Prominent Rust Primer and 1 coat Prominent Select Universal Undercoat.

Redecorating:
It is advisable to test the compatibility of coatings when redecorating is involved, i.e. paint a small section and then check the adhesion after 24 hours by applying a strip of masking tape and attempting to rip the paint off.

Gloss enamel:

• Sand down to a matt finish, spot prime exposed metal with Prominent Rust Primer and apply 1 coat Prominent Select Universal Undercoat.

Sound matt emulsion paint:

• Sand to matt finish, clean with ProGold General Purpose Cleaner diluted 1:10 with water and abrasive, rinse with water, allow drying and apply directly.

Sound sheen emulsion paint:

• Sand to matt finish, clean with ProGold General Purpose Cleaner diluted 1:10 with water and abrasive, rinse with water, allow drying and apply directly.

Poor condition surfaces, i.e. excessive peeling:

• Strip down and treat as per new work.

It is advisable to test the compatibility of coatings when redecorating is involved, i.e. paint a small section and then check the adhesion after 24 hours by applying a strip of masking tape and attempting to rip the paint off.

Limitations

• Cannot be applied to unprimed surfaces.
• Apply only under specified conditions.
• Colour changes generally first require a coat of Prominent Paints Select Universal Undercoat.
• Very cold conditions will lengthen the drying time.
• Moisture content must not exceed 15%.
• Apply to the correct spreading rates and adhere to the correct recoating times to prevent wrinkling.

Safety

• Keep out of reach of children.
• Ensure to maintain good ventilation during application and drying process.
• Wear a suitable dust mask if sanding.
• In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In the event where product came in contact with eyes rinse immediately with running water and seek medical advice.
• If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
• Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available from Prominent Paints Customer Service Department.
• To avoid any risk of spillage, always transport in a secure upright position.

• Keep out of reach of children.
• Ensure to maintain good ventilation during application and drying process.
• Wear a suitable dust mask if sanding.
• In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In the event where product came in contact with eyes rinse immediately with running water and seek medical advice.
• If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
• Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available from Prominent Paints Customer Service Department.
• To avoid any risk of spillage, always transport in a secure upright position.