Prominent Paints
Prominent Paints - More than just paint
Prominent Paints - More than just paint

PRODUCTS

RANGES

  • High Performance
  • Premium
  • Ultra
  • Neutron
  • Select Range
  • Speciality
  • Woodpro
  • Industrial
  • Trade
  • Effects
  • Primalex


BY APPLICATION

  • Interior
        Ceilings
        Other
        Trims
        Walls
        Wood
  • Exterior
        Ceilings
        Other
        Trims
        Walls
        Wood
  • Roof & Floor
        Paving
        Roof
        Roof & Paving
        Stoep
        Workshop Floor
  • Industrial
  • Wood
        Other
        Paint
        Sealer
        Varnish
  • Decorative Effects
  • Waterproofing
  • Interior & Exterior
        Ceilings
        Other
        Trims
        Walls
        Wood
  • Primers


Prominent Premium Satin Silk

Prominent Premium Satin Silk

A superior quality, fully washable acrylic with a soft, luxurious satin smooth finish.

Products Applications:
Ceilings (Interior), Ceilings (Exterior), Interior, Walls (Exterior), Walls (Interior), Wood (Exterior), Wood (Interior), Exterior and Interior & Exterior

Purchase:
Prominent Premium Satin Silk is available in the following sizes: 1lt , 5lt and 20lt


AVAILABLE IN THE FOLLOWING COLOURS

Please note: Every care has been taken to ensure that the colours displayed on this website reflect the actual paint colour as accurately as possible. Colours may vary due to your screen settings and resolution. Always consult a Prominent Paints colour card or stripe card before making your final colour choice.

WICKER
2108-Y47R
BARLEY SILK
2207-Y37R
GECKO
4705-Y24R
Also available in 20L
MISTY MORNING
1403-Y51R
MARBLE
0403-Y22R
AFRICAN IVORY
1107-Y36R
WHITE CLOUD
0702-Y
MARZIPAN
1504-Y35R
ICE-CREAM
0607-Y26R
BROKEN WHITE
0908-Y29R

PRODUCT DETAIL

Appearance: Sheen
Spreading Rate: 6 - 10 m²/litre, dependent on surface texture and porosity.
Solids: ± 55% by mass and 35% by volume.
Density: 1,35 kg/litre.
Recommended Dry Film Thickness: 2 coats at 35 µm per coat minimum.
Viscosity: ± 100 Kµ
Flash Point: Non-flammable

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt, 5Lt, 20Lt
Colours: White and colours as per colour card. Tint bases to tint most of the colours on the tint system.
Life Expectancy: 12 years, interior & exterior.
Calculated Maximum VOC: 16g/L maximum for white and pastel tinting base and selected standard colours.

Respecting The Environment:

  • Lead free & low VOC.
  • Dispose of excess product and containers in a responsible manner without harming the environment

TECHNICAL DATASHEET

Features

  • Non-yellowing: Unlike alkyd based paints, whites remain white.
  • Waterbased: Easy cleaning, low odour and quick drying.
  • Resist staining: Easy to clean and remove dirt and grime.
  • Hardwearing and washable
  • Good adhesion: Can be applied to previously coated, sound surfaces.
  • UV Resistant: Does not chalk on outside exposure – normal fading of colours can take place over time.
  • Can be tinted to specific colour requirements.
  • Lead free and low VOC: Reduces the odour associated with painting indoors.

Intended Usages

  • Formulated for use on correctly primed interior and exterior surfaces such as walls, wood, fascias and steel.

Application Details

  • Mixing: Stir before use with a flat paddle to an even consistency. Stir occasionally during use.
  • Method: Roller, brush or airless spray gun.
  • Thinning: Not recommended.
  • Cleaning: Tap water. Remove as much of the product as possible from the application equipment before cleaning with water.

Conditions:
Temperature between 5°C and 40°C. Relative humidity of less than 85%, preferably between 10:00 and 16:00. Ideally apply when the temperature of the substrate is at least 2°C above dew point. If possible away from direct sunlight.

Drying time:
Touch dry - 1 hour at 23°C. Note: Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Recoating time:
4 hours at 23°C.

Requirements:
Two coats.

Surface Preparations
Exterior cement plaster and fibre cement:

  • One coat Prominent Dampcure or Prominent Plaster Primer.

Wood:

  • One coat Prominent Wood Primer.

Mild steel:

  • Degrease, etch and clean with ProGold General Purpose Cleaner/water mixture (1:5) and scouring pad to remove any oily layer or rust and rinse thoroughly.
  • Apply one coat Prominent Rust Primer.

Galvanised iron:

  • Degrease, etch and clean with ProGold General Purpose Cleaner/water mixture (1:5) and scouring pad to remove any oily layer or oxidation, rinse thoroughly and apply one coat Prominent Acrylic Galvanized Primer.

Gloss Enamel:

  • Sand well, clean and apply Prominent Premium Universal Undercoat.

Emulsion paint:

  • Clean well and apply directly.

Chalky surfaces:

  • Wire brush/high-pressure water wash at 180 bar and a rotating nozzle and allow curing.
  • Apply one coat Prominent Dampcure or Prominent Surface Restorer.

Poor condition surfaces:

  • Strip down and treat as new work.

Limitations

  • Can only be applied under specified conditions.
  • Cannot be applied over poor quality undercoats or directly onto gypsum plaster.
  • Cannot be used for bridging hairline cracks.
  • Spot touching-up over large areas will be noticeable.
  • The low VOC compliance is applicable on white, pastel tinting base and selected standard colours for batches manufactured from 1 September 2010 onwards.
  • To ensure a consistent appearance ensure that batch numbers on all the containers are the same. Where the batch numbers differ, intermix before use.


Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • If the surface to be painted is asbestos then the preparation, cleaning and/or removal of broken asbestos sheeting needs to be done in compliance to the Asbestos Regulations, 2001 of the Occupational Health and Safety Act 1993. (ACT NO 85 of 1993). Contact Prominent Paint Technical Department on 0861 776 646 or 011 389 4746 if a copy of the Asbestos Regulations is required.


Tint Bases
The tint base containers are only filled to levels which are specific for each tint base to allow the calculated volume of colourant to be added in order to achieve the volume indicated on the container after tinting. Tint bases and colourants are unfinished products which should not be used on their own. Only once the prescribed colourant is added to the specific tint base will the finished product comply with the technical features and related information as set out in this TDS. The calculated max VOC compliance < 16g/L is only applicable to product tinted from Pastel Base excluding Clear Base.

Colourant to be used:
Prominent colourants are lead free specifically formulated for use with Prominent Pro-Matic tinting system. ICC colourants which are lead free using only Prominent supported formulations on Largo 2000.

Tint Bases:
Pastel Tint Base and Clear Tint Base.

PRODUCT SAFETY

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • Wear a suitable dust mask if sanding.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Do not smoke while painting.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • If the surface to be painted is asbestos then the preparation, cleaning and/or removal of broken asbestos sheeting needs to be done in compliance to the Asbestos Regulations, 2001 of the Occupational Health and Safety Act 1993. (ACT NO 85 of 1993). Contact Prominent Paint Technical Department on 0861 776 646 or 011 389 4746 if a copy of the Asbestos Regulations is required.